Body
Like other Land Rover vehicles, most of the Range Rover's bodywork skin is constructed from lightweight aluminium, except for the two-section rear upper and lower tailgates, the rear corners adjacent to the tailgate and the bonnet on all but the earliest models. Apart from minor cosmetic changes,[9][10][11] the body design changed very little in its first decade. However, while utility Land Rovers had body panels rolled from a single sheet of aluminium, the Range Rover used aluminium panels hung on a steel 'safety frame' (a method pioneered with great success on the Rover P6 saloon). This allowed the bodywork of the Range Rover to carry much greater structural strength with the steel frame while retaining the corrosion-resistant and easily repaired aluminium outer panels. While the steel frame was designed by the engineering team, it was expected that Rover's stylist David Bache would provide a design for the outer panels for use on the production vehicles. For the prototypes the engineers designed their own functional body panels simply to protect the occupants and to allow the vehicles to be driven legally on the road. However the clean, square-cut and functional design of the prototype was deemed so good that Bache only altered the detailing, such as providing a different front grille and headlamp design. The Range Rover also marked the first appearance of Bache's trademark "symmetric" dashboard, where a common moulding was used for the fascia superstructure on both RHD and LHD versions, onto which the pod-style instrument binnacle was simply mounted on the appropriate side – Bache would use this concept again on both the Rover SD1 and the Austin Metro in later years. The original fascia would later be nicknamed the "Airfix Dashboard" by Range Rover enthusiasts owing to its hard, low quality plastics which, as the vehicle moved upmarket over the years, betrayed its humble beginnings as a utility vehicle, It remained with the Range Rover up until the very last years of production when it was replaced by the "soft dash" (see below)
Early vehicles may be distinguished by the rear 'C' pillars being absent of a vinyl covering which was introduced a little later in the 1970s.
One of the first significant changes came in 1981, with the introduction of a four-door body. Until then, Range Rovers only had two doors for the sake of body strength, making access to the rear seats – especially ingress – rather awkward. These doors were also very large and heavy. Egress was somewhat alleviated by the special design feature of having two inside door-opening latches: latches in the front of the doors for the driver and front passenger, and a second set of equally large and prominently styled door-opener latches on the inside rear of the doors (behind the front seats), providing rear seat occupants full autonomy to leave the vehicle. They could easily fold the seats in front of them forward, and open the door from their rear seat locations in a somewhat convenient manner.
Several companies offered conversions to four-door Range Rovers in the late 1970s. One of these companies' conversions, by Monteverdi, was even approved by Land Rover to retain warranty after it was presented at the 1980 Geneva Salon. Two years earlier, British Leyland had restructured and promoted Land Rover into its own BL subsidiary and the now more independent company used the Monteverdi as a basis for producing its own four-door model in July 1981.[12] The four-door version was well received by the public — its popularity was such that the two-door was discontinued in the United Kingdom in 1984,[13] although the two-door continued to be produced through January 1994, mainly for the French market.[14]
The first major push upmarket was in 1984, which saw the availability of leather trim, unhinged rear number plate and a new 4-speed ZF automatic transmission; this was followed by the 1985 model year, which saw the instrument pod replaced by a more modern one (adapted from the Austin Maestro) and new door cards (using Austin Metro door handles) with walnut inlays.
The front end of the Range Rover was revamped in 1986. This brought a more pedestrian-friendly plastic grille with horizontal slats, and optional front valance with two fog lights. The seat base was lowered and door handles were redesigned, making it more difficult for rear passengers but greatly improving the comfort for taller people in the front. The dashboard switchgear was updated again, now featuring steering column stalks from the Austin Montego, and other miscellaneous items from the Austin Rover car range. Other changes included the windows, tailgate and bonnet, but none of those affected the general design. Bonnet and door hinges gradually evolved out of sight and the fuel filler cap was hidden behind a hinged flap. The last major change to the interior took place in 1994, when the Range Rover was re-designated "Classic" upon the arrival of the replacement P38A version. The car gained a 'soft feel' safety dashboard (derived from that used in the facelifted Series 1 Discovery) with new switches (these were lifted from the Rover 800) and instruments. These end of the line models are popularly called "soft dash" models by the motor trade and by enthusiasts to distinguish them from other members of the Range Rover Classic series.
