History
Dolby Labs became involved in movie sound when film studios used Dolby A type noise reduction on studio magnetic film recordings. The first film to use Dolby noise reduction throughout the production process is A Clockwork Orange (1971), though much of the benefit was lost when it was released with a standard "Academy" optical soundtrack. This led to a proposal from Dolby that A type noise reduction be applied to the optical soundtrack on release prints.[5]
Through the early 1970s, there was renewed interest in improving the quality of optical soundtracks, which had changed little since the 1930s. In particular, the infamous "Academy curve" (the standard frequency response for cinema playback of optical tracks as specified by the Academy of Motion Picture Arts and Sciences in 1938) was still in use. It involved a drastic roll-off in the high-frequency response of the theater system with the intention of reducing the audibility of noise and distortion. Dolby proposed replacing the Academy curve with Dolby A type noise reduction on the track. Starting with the 1974 film Callan, ten films were released with a Dolby encoded mono soundtrack. Theaters were equipped with a Dolby A type noise reduction module and a third-octave equalizer to equalize the electro-acoustic frequency response of the speakers/auditorium. It created a new international standard for cinema sound.[6][7]
Though the system worked well, theater owners were reluctant to invest in the technology until stereo was added to the mix. The idea of putting a two-channel optical stereo soundtrack in the normal soundtrack area of a film print was not new; the stereo pioneer Alan Blumlein had made experimental stereophonic films using such a system as early as 1933, and J. G. Frayne of Westrex had proposed a similar system to the SMPTE in 1955.[8]
By 1970, however, it was apparent that magnetic recording methods were not going to displace optical soundtracks on most release prints, and in the early 1970s Eastman Kodak revived the idea, as described by R. E. Uhlig in a paper presented to the SMPTE in 1972.[9] Initially using a two-channel 16mm film recorder built for them by RCA, Kodak recorded two-channel stereo soundtracks much as Blumlein and Frayne had done before, but added Dolby noise reduction to improve the limited dynamic range available from these half-width tracks.[7]
The remaining problem was the lack of a center channel, regarded as essential to lock dialogue to the middle of the screen. Uhlig discussed this issue in a follow-up paper.[10] He considered the possibility of splitting the soundtrack area three ways to provide a third center channel, but dismissed it because of the negative impact it would have on dynamic range and the problems involved in converting film projectors. Instead he suggested feeding a center-channel speaker with a simple mix of the left and right channels; however, this is not entirely satisfactory as it degrades the stereo separation. After he brought his idea and worked with Dolby, Dolby SVA, a 35mm stereo variable-area optical encoding and decoding system, came up and later was adopted as an industry standard--ISO 2969.[1]
At this time, Dolby joined forces with Kodak in developing this system. Dolby's solution to the center-channel problem was to use a "directionally enhanced" matrix decoder, based on those developed for domestic "Quadraphonic" systems, to recover a center channel from left and right channels recorded on the film. The matrix decoder originally employed for this used the Sansui QS matrix under license. This system was used for the 1975 Ken Russell film Lisztomania.
The matrix was then extended to provide a fourth channel for surround loudspeakers, allowing for a 4-channel system with the same speaker layout as the CinemaScope 4-track magnetic stereo system of the 1950s, but at a far lower cost.
Dolby Stereo, as this 4-channel system was now branded, was first used in 1976's A Star is Born. From spring 1979 onward, a new custom matrix replaced the Sansui QS matrix. It was first used in that year's Hair and Hurricane.[11][7]
At first, Dolby Stereo equipment was installed mainly in larger theaters already equipped with amplifiers and speakers for CinemaScope 4-track stereo. But the success of 1977's Star Wars, which used the 4-channel system to great effect, encouraged owners of smaller theaters to install stereo equipment for the first time.
A key feature of this system was its backward compatibility: the same print could play anywhere, from an old drive-in theater with mono sound to a Dolby Stereo-equipped cinema, eliminating the need for a costly double inventory of prints for distribution. The success of Dolby Stereo resulted in the final demise of magnetic stereo on 35mm release prints. From then on, only 70mm prints used magnetic sound.
In the early 1990s, Dolby SR noise reduction began to replace Dolby A type NR in 35mm motion picture exhibition. All release prints encoded with Dolby Digital include a Dolby SR analog soundtrack, both as a backup in case the digital track malfunctions and for theaters not equipped for Dolby Digital playback.
As of 2021, Dolby Stereo's market share in the cinema space has declined rapidly with the advent of digital cinema. It serves as a backup for movie theaters still exhibiting 35mm film.
The Dolby Stereo Matrix
The Dolby Stereo Matrix (or Dolby 4:2:4 Matrix)[12] is straightforward. The four original channels of Left (L), Center (C), Right (R), and Surround (S), are combined into two, known as Left-total and Right-total (LtRt)[13][12] by this formula:
where j = 90° phase-shift
This center channel information is carried by both Lt and Rt in phase, and surround channel information by both Lt and Rt but out of phase. This gives good compatibility with both mono playback, which reproduces L, C and R from the mono speaker with C at a level 3dB higher than L or R, but surround information cancels out. It also gives good compatibility with two-channel stereo playback where C is reproduced from both left and right speakers to form a phantom center and surround is reproduced from both speakers but in a diffuse manner.
A simple 4-channel decoder could simply send the sum signal (L+R) to the center speaker, and the difference signal (L-R) to the surrounds. But such a decoder would provide poor separation between adjacent speaker channels, thus anything intended for the center speaker would also reproduce from left and right speakers only 3dB below the level in the center speaker. Similarly anything intended for the left speaker would be reproduced from both the center and surround speakers, again only 3dB below the level in the left speaker.
