PD4
The first Australian Dodge Phoenix, coded the PD4, was released in May 1960. A Canadian Dodge with a Plymouth dashboard, it was imported in CKD packs and assembled at Chrysler Australia's Mile End, South Australia Mile End facility. The PD4 Phoenix was offered only as a 4-door sedan, in two trim levels, the De Luxe and the Luxury Liner.[8] The PD4 had a 118-inch wheelbase and was powered by a 318 cubic inch OHV V8 engine. The Phoenix name was derived from the Dodge Dart Phoenix,[9] on which it was based.
RD4
The RD4 Phoenix of 1961 used the cabin section of the PD4 with new front and rear bodywork.[10] Dimensions remained unchanged, as did the mechanical specifications,[10] again being based in the North American Dodge Dart.
SD2
The SD2 of 1962 featured a shorter 116 inch wheelbase and a completely new body which was both shorter and narrower than its predecessor[10] being now based on the downsized US Dodge Dart.
TD2
The TD2 of 1963 was the first Phoenix to be based on the renamed Dodge 440 model,[10] with Dodge moving the Dart name to the new compact A-body line. The 4 door sedan body style and the 318 cubic inch engine were retained.[11]
VD2
The VD2 Phoenix was introduced in 1964.[11] The wheelbase was now 119 inches and the overall length increased by four inches to 212.[10] The VD2 was based on the 1964 North American Dodge 440.
AP2D
The AP2D Phoenix was introduced in 1965.[11] This model was a rebadged Canadian Plymouth Fury III,[10] a strategy that Chrysler Australia would continue through to the end of 1972.[10] The 1965 model featured vertically stacked four-headlight frontal styling.[10] The 318 cubic inch engine were retained.[11] A Plymouth hood ornament was used, with the Dodge "Fratzog" superimposed over the Plymouth outline.
DB6
The 1966 Phoenix was coded DB6.[11] Changes follow the 1966 Fury III; a new grille, revised rear panels, new taillights and a new bootlid.[10]
DC
The 1967 Phoenix was coded as the DC series.[12] It was the first Phoenix to be available with a choice of bodystyles, a 4-door hardtop now offered in addition to the 4 door sedan. The sedan retained the 318 cid V8 engine and while the hardtop was fitted with a 383 cid V8. In the later part of 1967 Chrysler Australia shifted Phoenix assembly from Tonsley Park to its Port Melbourne facility.[10]
DD
The 1968 Phoenix was coded DD.[12] The main changes for 1968 were new rear sheet metal and new taillights.[10] Round side marker lights were introduced, the same ones used on the North American Plymouth Fury.
DE
The DE Phoenix was introduced in 1969.[11] The new model featured horizontal dual headlights,[4] and a 120-inch wheelbase.[10] Overall length was now 214.5 inches.[10] It was marketed as the 400 Limited Edition series with each car carrying a numbered dashboard badge.[10] Production was planned to be limited to 400 sedans and 400 hardtops, although actual production did not reach 400 units of either. 371 examples of the DE were built at Chrysler Australia's Port Melbourne facility in 1969 and a further 385 in 1970.[13] For the first time, DE models featured hidden, parallel-action windshield wipers. The body was completely new and featured the Plymouth Fury "Fuselage" curved sides.
DF
The DF Phoenix was introduced in 1970. Again it was marketed as the Phoenix 400 with sedans and hardtops carrying individually numbered dash plaques. 298 were built at Port Melbourne in 1970 and 110 in 1971.[13]
DG
The DG Phoenix was introduced in 1971, again as the Phoenix 400 with individually numbered sedans and hardtops. 298 were built at Port Melbourne in 1971.[13]
DH
The DH Phoenix was introduced in 1972.[13] 73 were built at Port Melbourne in that year.[13] A decision to close the outdated Port Melbourne facility led to the discontinuation of the Phoenix.[14]
